Vicmarc

Please note: for insert type chuck, an appropriate insert to fit your lathe is required. Drill a perfectly centered hole in your blank on your lathe using this unique lathe chuck...

The Vicmarc Sharpening Jig is used to sharpen bowl gouges, spindle gouges and a variety of other tools.  The unique design of the Vicmarc Sharpening Jig gives you extra swing...

For the old VL100 Vicmarc Lathes or any Lathe that has a 5/8" post Lenght of Post 2"

Cast Iron

Cast Iron

Cast Iron

The Manta Gauge Master was designed by Vicmarc and DNS Germany. The advantages of the Manta are: Reduction of the edge angles to easy-to-remember numbers. Reduction to 5 edge angles of...

3/4" OD Reduction Bushes are available in four sizes.  Hole Diameter  Part Number 6mm V01256 9.5mm (3/8") V01257 12.7mm (1/2") V01258 15.8mm...

3/4" OD Reduction Bushes are available in four sizes.  Hole Diameter  Part Number 6mm V01256 9.5mm (3/8") V01257 12.7mm (1/2") V01258 15.8mm...

3/4" OD Reduction Bushes are available in four sizes.  Hole Diameter  Part Number 6mm V01256 9.5mm (3/8") V01257 12.7mm (1/2") V01258 15.8mm...

3/4" OD Reduction Bushes are available in four sizes.  Hole Diameter  Part Number 6mm V01256 9.5mm (3/8") V01257 12.7mm (1/2") V01258 15.8mm...

65mm Quill Travel

Type a description for this product here...

Complete assembly with bearings

Extra long VM100 chuck wrench used when using large jaws such as bowl jaws on you VM100 chuck

Extra long wrench for VM1200 chuck when using bowl jaws

This insert will adapt the Vicmarc VM120, VM140, and VM150 chucks to any lathe with a 1" x 8tpi Spindle thread. Vicmarc's Eccentric chucks and the Vicmarc Oval Device also accept this insert All...

This insert will adapt the Vicmarc VM120, VM140, and VM150 chucks to any lathe with a 1-1/4" x 8tpi Spindle thread. Vicmarc's Eccentric chucks and the Vicmarc Oval Device also accept this...

helpful for tightening or removing inserts on chucks or VOD

Female thread: 1" x 8tpi Male thread: 1.5" x 8tpi    

Female thread: 1" x 8tpi Male thread: 1.25" x 8tpi

Female thread: M33 x 3.5 Male thread: 1" x 8tpi

The Eccentric Chuck #4 is designed and manufactured by Vicmarc Machinery and it expands the possibilities for off center turning. This version has a direct thread of 1-1/4"x8tpi. The main feature of...

The Eccentric Chuck #4 is designed and manufactured by Vicmarc Machinery and it expands the possibilities for off center turning. The main feature of the chuck is its infintely variable axis setting...

Used to set a height on your toolrest allowing you to unlock the toolrest and swivel/move the toolrest without changing the set height.

For VM90/100. These can be used instead of the traditional faceplate. They allow remounting of prepared blanks by mounting directly onto the chuck jaws. Also can be used for turning green wood that...

The adjustable jaws allow you to re-chuck bowls for finishing the bottom or do light clean-up work on the foot of the bowl. To mount the bowl, the bowl is reversed and held by the rim, either...

By removing one or more of the dovetail segments from these jaws, they are adaptable to a variety of uses. The sizes indicated on the drawing are when the jaws form a perfect circle, which is...

Shark Jaws have serrated inner and outer jaw surfaces. These extended jaws provide an aggressive hold. They hold cylinder spigots much more safely than standard jaws. They are much easier and...

Oval turning is an old art of turning, it has been practiced since the middle ages. Professor Johannes Volmer was able to create a system for oval turning using tooth belts for smooth operation...

150mm toolrest for the old VL100 mini lathe, no longer in production

80mm toolrest for the old VL100 mini lathe, no longer in production

These Rotating Unions have a dovetail pickup to suite a self-centering four jaw chuck. It can also be mounted directly to the lathe spindle with an M45x2 internal thread , which requires a VM120/150...

Vacuum plate can accept a VM90/100 insert and be mounted directly to the lathe spindle. If used on a Vicmarc Lathe in this configuration, the V01215 M16 x 1.5 Rotating Union is required. It can also...

This chuck is threaded directly, meaning it will mount directly onto the lathe spindle without an insert. Now available in 1"x8tpi and 1-1/4"x8tpi The VM100 T - Bar Allen Key operated chuck allows...